8'6" WIDE X 18' LONG FOOD TRAILER

WWT MFG has been specializing in custom concession trailers, catering trailers, kitchen trailers and BBQ smoker trailers for over 20 years now. It's a piece of mind knowing your food trailer is backed by an established company. For more information or for a "FREE" custom quote, please give us a call at 912-283-7551 or email www.WWTMfg.com.

THIS CONCESSION TRAILER INCLUDES THE FOLLOWING:

1. 8'6" wide x 18' long WorldWide Trailer Manufacturing Mobile Kitchen Trailer, model MK182-8
2. Custom reinforced walk on roof
3. Two - pairs of heavy duty scissor type stabilizer jacks located on front & rear of trailer, 5000 lb static load capacity each
4. Two - custom fabricated steel tread plate propane platforms for 100# LP tanks each welded to the trailer frame for solid support – Note: steel platforms are covered with ATP (Aluminum Diamond Tread Plate)
5. Two - custom fabricated upper & lower steel propane tank mounting brackets to secure LP tanks firmly in place – brackets are through bolted to front wall for extra support
6. Two - 100 lb propane tanks with a 950,000 BTU 2 stage regulator
7. Extended three piece 'A' frame (5' long tongue) with a heavy duty tongue jack & sand pad
8. 2 5/16" top mount coupler with replaceable locking dog assembly
9. D.O.T. compliant 5/16" safety chains with Clevis safety slip hook & latch
10. 6"x2" rectangular steel tube main rails with equal height 'C' section cross members with square outriggers & steel side plates - steel cross members on 16" center
11. Two – 5,200 LB, (10,400 GVWR) 10 degree up torsion axles with 12" x 2" electric brakes, E/Z lube, & 6 on 5.5 hubs & drums with weather resistant wiring package
12. Four - ST225/75R15 load range 'D' radial tires mounted on a 6 bolt electro deposition coated silver spoke wheel
13. Chassis fully under coated with CPC (Corrosion Preventative Compound)
14. Food trailer has 7’ interior height
    
15. Install 60" long commercial stainless steel NSF APPROVED hood with a high up blast grease extracting exhaust fan with on/off wall switch – hood also includes filters, grease cup & grease tray (Note: there is no space between the top to the hood & ceiling to clean)
16. Custom curbside 3 section TEMPERED GLASS SERVING WINDOW (45" high x 69" wide), comes with 1 display/picture window & 2 vertical slider windows with screens (16" mesh) for serving customers – includes custom lift up awning with 2 keyed flush locks for security & gas assist awning rods to raise & secure awning in upright position
17. 36" wide lockable pre-framed rear entry door with screen (16" mesh), flush lock & integrated dead bolt
18. ¾” exterior grade plywood floor
19. Non-porous and easily cleanable one piece heavy duty commercial grade RTP (Rubber Tread Plate) flooring over exterior grade plywood floor
20. Smooth and easily cleanable non-porous white aluminum ceiling liner with no exposed utility lines, piping, conduit or wiring – bonded for a smooth look
21. Smooth and easily cleanable non-porous white aluminum interior sidewall liner with no exposed utility lines, piping, conduit or wiring – bonded for a smooth look
22. Fully insulated sidewalls and ceiling
23. Custom 96” long white laminated interior overhead cabinet with latching cabinet doors along front wall above the sink assembly
24. Custom 12" deep x 120” long white aluminum interior overhead storage tray/shelf along curbside wall for additional storage space
25. Custom 24" deep x 91" long x 30" high white laminated interior counter along curbside wall
26. Custom 10” deep x 69” long stainless steel exterior fold down condiment counter in front of curbside serving window
27. 100 amp, 120/240v service panel/box with a 100 amp main breaker, 20' shoreline power cord for your electrical connection and through floor cable hatch to run your power cord outside
28. Nine - 20 amp, 120v GFI duplex wall receptacles – Note: cord drops used where applicable
29. Three - LED light fixtures with diffuser covers - includes on/off wall switch
30. Custom L-shaped white laminated enclosure/cabinet with latching cabinet doors for commercial NSF APPROVED stainless steel 3 compartment sink with single faucet & integrated drain boards on each side (bowl size approx. 15x15x12) - includes separate stainless steel hand sink & faucet with divider/splash guard to separate the hand sink from the 3 compartment sink - all sinks will have hot & cold running water under pressure
31. Removable cutting board (NSF or equal) to place over the 3 compartment sink (gives you additional prep/work space)
32. On demand water pump with on/off wall switch
33. 50 gallon fresh water tank (NSF or equal) located under the sink assembly concealed in custom cabinet enclosure for a clean and professional look - 1/2" hot and cold NSF Pex water lines
34. 6 gallon, 120v hot water heater located under the sink cabinet/enclosure
35. Outside water hook up with back flow preventer to easily fill your water tank or to connect to city water - includes keyed locking door to prevent vandalism, dust & grime
36. Two - 30 gallon waste water holding tanks plumbed together (60 gallon total capacity) located under the trailer lower and away from the fresh water tank per regulatory requirements - includes waste vent stack, 1 1/2" PVC drain lines & back flow preventer per code (Note: waste tank is 15% larger & or greater than water tank)
37. A dump valve located under the trailer for easy waste removal
38. .030 pre-finished "BRONZE" exterior aluminum "BONDED" for a smooth look
39. Aluminum teardrop fenderettes over wheel wells
40. 120v, 15,000 BTU roof mounted air conditioner with a 5600 BTU heat strip
    
41. 14"x14" screened (16" mesh) translucent roof vent with crank – includes a Maxxair roof vent cover for rain protection while vent is open
42. S.A.E. color coded 12v electrical system, D.O.T. required exterior lighting package
43. D.O.T. 'A' frame (tongue) mounted battery with breakaway switch – NOTE: mount battery as far away from generator as possible
44. 7 way round trailer end connector (7 way RV blade style) - designed to plug in to the tow vehicle’s 7 way round connector
45. Custom anodized front and rear corner covers
46. Four - chrome ABS hub covers and trim rings
47. Custom platform with step up for chest freezer
    
48. Three - single exterior flood lights on GFI breaker with interior on/off switch
49. 30" x 15" slider window with screen (16" mesh) centered on front wall above the 3 compartment sink
    

NOTE: ALL 120v WIRING IS 12 GAUGE WIRE RAN IN MC CABLE. IN ADDITION, ALL OUTLETS ARE GFI RATED FOR COMMERICAL USE.

THIS CONCESSION ALSO INCLUDES THE FOLLOWING EQUIPMENT:

***NOTE***All equipment is secured and non-movable

1. NSF APPROVED 60” long commercial stainless steel hood system with a high up blast grease extracting exhaust fan with an on/off wall switch
2. NSF APPROVED 19 cu. ft. commercial stand up refrigerator
3. NSF APPROVED 48" two door commercial stainless steel sandwich prep unit with top pans, lid & cutting board along front
   
4. NSF APPROVED 24" commercial stainless steel LP flat top griddle
5. NSF APPROVED commercial stainless steel 4 burner LP range with oven
   
6. NSF APPROVED 24” commercial stainless steel equipment stand with an adjustable underneath shelf for griddle
   
7. NSF APPROVED 24” long x 24” deep commercial stainless steel work top table with an adjustable underneath shelf for additional prep space
8. NSF APPROVED 48” long x 30” deep commercial stainless steel work top table with an adjustable underneath shelf for additional prep space
9. Paper towel holder and soap dispenser next to the hand sink
10. ABC fire extinguisher
11. 5 cu. ft. chest freezer
12. 88” long x 48" high stainless steel back splashes behind the cooking equipment
13. Compliance stickers/decals affixed to trailer --- “GAS SHUT OFF VALVE” & “DANGER PROPANE NO SMOKING”

ADDITIONAL SERVICES INCLUDED:

1. Run LP service for cooking equipment - includes schedule 40 black iron pipe with main interior and exterior shut off valves, each piece of equipment will have its own dedicated shut off valve as well - corrosion resistant PVC coated stainless steel flexible hoses will be used to make final connection to non-movable equipment (its the customer's responsibility to fill LP tank with propane - tank/s are new and will need to be purged prior to use - any fill station will be able to perform this, just let them know the tank is brand new, never filled - a leak down test is performed prior to pick up/delivery and should be checked periodically thereafter by Buyer)

For more information, please call 912-283-7551 or email, WWTMfg@aol.com